Fleischmann profi boss инструкция на русском

[Page 1] Fleischmann PROFI-BOSS 686601

…

[Page 2] Fleischmann PROFI-BOSS 686601

…

[Page 3] Fleischmann PROFI-BOSS 686601

G Operating Instructions The model railway for experts PROFI-BOSS 686601 DCC Digital Controller Locos Points LocoNet 
…

[Page 4] Fleischmann PROFI-BOSS 686601

1. Advice on Use and Warning G Safety instructions ➜ The PROFI-BOSS is not suitable for use by children under three years of age. ➜ The PROFI-BOSS may only be used in conjunction with the plug-in mains transformer provided, or with…

[Page 5] Fleischmann PROFI-BOSS 686601

➜ Netstroom adapters zijn geen speelgoed en dienen uitsluitend voor de stroomtoevoer van uw modelspoorweg. Controleer deze apparaten a.u.b. regelmatig op mogelijke schade aan behuizing, stekkers of draden en koppel deze in geval van beschadiging on…

[Page 6] Fleischmann PROFI-BOSS 686601

Basic Knowledge be run simultaneously. ➜ If desired, the round connecting cable can be inserted into the central slot down the rear of the hand controller. 2. Getting Started 2.1 Equipment and Functions In this chapter, you will discover how the P…

[Page 7] Fleischmann PROFI-BOSS 686601

For everyone who does not yet want to go deeper, but wants to get going straight away, the quick entry instructions are set out here (steps 1-6). If you just want to use the PB to run the loco in your start set, for example, and want to start running…

[Page 8] Fleischmann PROFI-BOSS 686601

Initial Knowledge Initial Knowledge transformer and the two separate wires (grey and violet) are joined to the track. The rectangular western plug is then inserted into the central (smaller) socket on the rear of the PB (not into the side socket alon…

[Page 9] Fleischmann PROFI-BOSS 686601

Initial Knowledge First we will show you how to switch the loco lights on and off, and alter the inertia settings for acceleration and braking, top speed, loco address, loco indi- cation, etc. The light on your loco can be turned on or off at any …

[Page 10] Fleischmann PROFI-BOSS 686601

cut off, the speed of the loco shown in the display will go to v=0. In the display ”—S-T-O-P—“ will appear. This is known as a ”complete emergency stop“. By pressing the red knob twice, 2 x , the power to the layout will be turned …

[Page 11] Fleischmann PROFI-BOSS 686601

We will use an electrical receiver module 6852 (=not contained in the start set) which has 4 output connection ready for use. Once we have connected them up according to their instruction leaflets, we are ready to opeate them using the PROFI-BOSS. �…

[Page 12] Fleischmann PROFI-BOSS 686601

Press the key number 9 The Point Nr. 9 will then spring from ”straight“ to ”curved“. Pressing the number 9 again will set the point back to ”straight“ again. You can use the same procedure for all the other points. Simply put in the poi…

[Page 13] Fleischmann PROFI-BOSS 686601

Press the key HOME and we can return to operational mode. The PROFI-BOSS is intelligent. It will re- member the accessory menu last displayed. When calling up the MAGNET menu again, it will automatically display the points 11 to 20 and not the p…

[Page 14] Fleischmann PROFI-BOSS 686601

➙ Press the key OK The display will automatically indicate the accessory group which contains the article address ”11“. This is especially useful for relatively high numbers so that you do not have to keep on scrolling upwards with the ke…

[Page 15] Fleischmann PROFI-BOSS 686601

5. Selecting Locos from the List Inside the PROFI-BOSS we have already installed a databank with capabilities and functions of several locos from our range. This will save you a lot of time (once you have altered the addresses) in extensive program-…

[Page 16] Fleischmann PROFI-BOSS 686601

The class 76 (Sound loco), along with all its pre-programmed capabilities will appear in the operational menu. Just as an example, we will turn off the fac- tory setting for the inertia F6 until we have gained a little more operational expertise. In …

[Page 17] Fleischmann PROFI-BOSS 686601

You have already found out how to select the menu points, change between menu levels, in short, the operation and we shall be utilis- ing this knowledge in the following sequences. We have set out a table on the following pages which shows ALL of the…

[Page 18] Fleischmann PROFI-BOSS 686601

3130 Locomotive Loco address Value ”X“ Loco databank Loco name/address CV direct input CV number Loco name/address Speed steps CV value address name Acceleration inertia ”function“ loco selection ”loco lists“ Breaking inertia CV value …

[Page 19] Fleischmann PROFI-BOSS 686601

You can access the ”settings“ menu by pressing and holding the ”C“ key and then pressing the ”alt“ key. Important: In order to ensure that the PROFI-BOSS stores your alterations, you must confirm the input with ”OK“ or ”PROG“ (acc…

[Page 20] Fleischmann PROFI-BOSS 686601

The PROFI-BOSS will now search through to read out the address of the decoder of your loco. This will be shown by the two question marks alongside the ”value“. If the read out procedure (as with all FLEISCHMANN DCC-decoders) has been successful, …

[Page 21] Fleischmann PROFI-BOSS 686601

The PROFI-BOSS offer you the possibility to set up a databank which contains only your personal locos. This databank is titled ”my databank“ and is empty when the PROFI-BOSS is delivered. Using the following example, you will see how it can be fi…

[Page 22] Fleischmann PROFI-BOSS 686601

Come out of the the databank now by press- ing ”menu“ to return to the running mode. If you have some more locos to change address or put into ”my databank“ then sim- ply repeat this procedure again. Advice: Now you have a second databank wit…

[Page 23] Fleischmann PROFI-BOSS 686601

41 ❖ Menu maximum speed: Here you can set the value for the maximum speed of your loco (value area 0-255). Input via the keyboard or the ❖ Menu trim forwards: Here you can set the value for the trim forwards (=individual suitable speed) of you…

[Page 24] Fleischmann PROFI-BOSS 686601

43 databank ”my databank“ (switchable with the ”alt“ key). In these lists (=loco databanks) where the locos have been stored according to their addresses, you can select any one of them for reprogramming. With the ”SEL“ you will come bac…

[Page 25] Fleischmann PROFI-BOSS 686601

45 The choice between impulse duration and output output can be switched using the keys Confirm the selection of the impulse duration with PROG. In this menu point, by pressing the alt key, it is also possible to choose for each output of the MA dec…

[Page 26] Fleischmann PROFI-BOSS 686601

47 1. Level/ 4. Main menu: PROFI-BOSS In the 1st level, find the main menu PROFI- BOSS. Here you can adjust the settings of the PROFI-BOSS controller, read out the soft- ware version and several more items which we can now go into a little further….

[Page 27] Fleischmann PROFI-BOSS 686601

❖ Menu MASTER If you intend to use the PROFI-BOSS in conjunction with other PBs, here you set which of them will be the master PB. (see additional for further information). If it is to be the master, then the other slaves connected to it using the …

[Page 28] Fleischmann PROFI-BOSS 686601

USING THE PROFI-BOSS WITH LOCONET CONNECTIONS Running the PROFI-BOSS in conjunction with the TWIN-CENTER If you are already the owner of a FLEISCH- MANN TWIN CENTER controller, then the PROFI-BOSS can be connected into it to be used as a slave contr…

[Page 29] Fleischmann PROFI-BOSS 686601

If however, you both wish to share the same loco databank, then this is also possible with- out needing to type all your loco data in all over again: In the setting area of each PB, you will find the entry ”Master“. This means that this PB has it…

[Page 30] Fleischmann PROFI-BOSS 686601

placed on the layout, the PB itself will auto- matically decide which loco can no longer be commanded. This loco will only receive its commands when called up again. SOUND FUNCTION SYMBOLS Here is a list of the available sound functions from the PB. …

[Page 31] Fleischmann PROFI-BOSS 686601

GEBR. FLEISCHMANN GMBH & CO. KG Postfach 910148 · D-90259 Nürnberg Telefon 09 11 / 3370 — 0 Telefax 0911 / 3370 — 2 99 E-Mail: [email protected] Internet: http://www.fleischmann.de Internet: http://www.profi-boss.de Made in Germany · Fabri…